Popular topics: Downloads Can I connect my computer wirelessly to the projector? HDL300 system installation guide Download Room Manager Room Manager features overview ► WM408i installation guide and drawings ► HDL300 system integration guide Microphone clearance requirements and recommendations More download options Does the HDL300 system work with audio conferencing (UC&C) software? Using the auxiliary ports on the HDL300 system Span Workspace technical requirements Installation guides and drawings Getting started with your HDL300 system HDL300 and Dual HDL300 system connection diagrams Installing a Dual HDL300 system Is the HDL300 system compatible with the Cisco® SX80? Can I switch between a single HDL300 and Dual HDL300 system? Copying and pasting onto the canvas Setting up Jira® for Span Workspace ►

What kind of auxiliary jacks are compatible with the HDL300 system?

Below are detailed descriptions on the auxiliary in and auxiliary out jacks.

Auxiliary input (In) jack

The 3.5mm stereo jack input connection is a single-ended, unbalanced signal and has a maximum input signal of 1 Vrms (2.83 Vp-p). The signal provided to this input needs to be checked for compatibility.

Any equipment providing voltages above this level (e.g. speaker levels) may result in clipping distortion and, in extreme cases, damage to the HDL300 system. Equipment providing voltages well below this level (e.g. microphone level vs. line-level) will not be adequate to drive the signal and may result in quiet or no audio on the channel. Before connecting to this port, check that the provided voltage levels are adequate or ensure that the levels are adjusted properly by additional interfacing hardware.

As the input is single-ended and therefore unbalanced, make sure the input audio signals provided into the In jack are single-ended. Balanced or differential outputs from the equipment could cause issues and may have to be adjusted with additional interfacing hardware. As the signal and cable are single-ended, the shorter the cable is the less noise will be coupled onto the signal, making the audio clearer.

The 3.5mm jack supports a standard TRS (tip-ring-sleeve) jack pinout with the left channel on the tip, the right channel on the ring and the ground on the sleeve (see diagram below). When mono audio is played over this channel, the same audio will be reproduced on both the left and the right channel. If a mono audio TS jack is plugged in, the right channel will be shorted to ground and only the left channel will be connected.

The HDL300 system speakers will play back sound from the connected source with the input jack. Both the USB and auxiliary jacks can be connected at the same time and may even be used simultaneously. In such a case, the input sources will be combined (between the input jack and USB auxiliary input). Therefore, switching between the input jack and USB is not required. If only the audio is being used from the USB and not the auxiliary jack, the nil input from the auxiliary jack will not impact the audio from the USB (and vice versa). In this configuration, make sure the device connected to the analog input jack will not generate any noise when it is idle, in standby, or off – otherwise it could interfere with the USB audio.

It is also possible for the HDL300 system to interface through the USB with an audio conferencing application and simultaneously connect through the auxiliary jack to an external device with analog source (such as a DVD player audio). This setup would allow the HDL300 system’s speakers to output either the audio conferencing channel, or the DVD audio to the room.

Auxiliary output (Out) jack

The connect module has a 3.5mm stereo output jack. By default, this output connection is a single-ended, unbalanced signal and has a default maximum output signal of 0.92 Vrms (2.6 Vp-p) into 10Kohm load. Any equipment requiring voltages below these levels (e.g., microphone levels as opposed to line-levels) may result in clipping, distortion and, in extreme cases, damage to connected systems. Equipment requiring voltages well above these levels will not be adequately driven by the HDL300 system’s output signal and may result in quiet or no audio on the channel. Before connecting to this port, make sure the provided voltage levels are adequate, or double-check that the levels are adjusted properly by additional interfacing hardware.

As the output is single-ended and therefore unbalanced, ensure that audio signals input of the attached equipment will be acceptable. As the signal and cable are single-ended, the shorter the cable is the less noise will be coupled onto the signal, making the audio clearer.

As with the input jack, the 3.5mm output jack supports a standard TRS (tip-ring-sleeve) jack pinout with the left channel on the tip, the right channel on the ring and the ground on the sleeve (see diagram below). If mono audio is played over this channel, the same audio will be reproduced on both the left and the right channel. If a mono audio TS jack is plugged in, the right channel will be shorted to ground and only the left channel will be connected.

The default signal provided by the output jack is microphone pickup that is echo-canceled. The signal is intended to be connected to equipment that will transmit audio to the far-end of the conference site. If the system connected to the HDL300 system also provides echo cancellation or additional processing of the audio signal, there may be some conflict in algorithms and therefore less-than-optimal performance. In this case, disable echo cancellation on the connected system (e.g., directly pass through audio).



Last updated: January 31, 2019

Was this article helpful?

Can’t find what you’re looking for?

Contact Support

1.844.370.2111